PRE1534 FORM MEASUREMENT SURFTEST SJ-410 SERIES Portable Surface Roughness Tester
2 Analysis functions that are a notch above the rest Portable Surface Roughness Tester Surftest SJ - 410 Series Easy and safe measurements that anyone can perform efficiently User benefit1 A higher-level of quality control User benefit2
3 Touch screen for easier operations The high-visibility color-graphic LCD touch screen clearly displays calculated results and assessed profiles. A backlight enables comfortable viewing even under poor lighting conditions. Space-saving dual functionality User benefit3 SJ-412 Traverse range 50 mm SJ-411 Traverse range 25 mm
4 Easy and safe measurements that anyone can perform efficiently User benefit1 The auto-set unit* enables measurements to be made with a single button push, saving you time and increasing work efficiency. Options for SJ-410 Series * This is an optional accessory for the SJ-410 Series. It can only be used on the simple column stand (optional accessory, order No. 178-039). When the units are used in combination, straightness for SJ-411 / 412 drive units will be degraded by about 0,2 µm. Cannot be used when the tester’s main unit is an older model (SJ-401 / 402). Auto-set unit* 178-010 This unit automatically completes a full measurement cycle of stylus contact, measurement, stylus retraction, and detector auto-return with just one button push (stylus retraction and detector auto-return can be switched on and off by operating the drive unit). X- ax i s ad j us tment un i t* 178-020 This unit helps fine-tune the horizontal (X axis) direction. Tilting adjustment unit* 178-030 This unit is used for aligning the workpiece surface with the detector reference plane. It supports the DAT function to make the leveling of workpiece surfaces easier. Complete set* Tilting adjustment unit 178-030 X-axis adjustment unit 178-020 Auto-set unit 178-010 12.5 mm 12.5 mm The auto-set function safely controls descent of the detector, eliminating the possibility of operator error causing damage to the stylus. ± 1,5° 10 mm Auto -set Retraction Autoreturn Measurement Optional stand shown (178-039) is required to use the Auto-set unit.
5 Simple column stand for SJ-410 Series <Option> 178-039 Vertical adjustment range: 250 mm Dimensions: 400×250×578 mm Mass: 20 kg A single measurement enables simultaneous analysis under two different evaluation conditions. A single measurement allows calculation of parameters and analysis of filtered profiles without the need for recalculation after saving data, contributing to higher work efficiency. Assessing a single measurement result under two different evaluation conditions This table helps make the alignment adjus tment s required when measuring c ylindrical sur faces . The correc tions for the pitch angle and the swivel angle are determined from a preliminar y measurement and the Digimatic micrometer s are adjus ted accordingly. A flat- sur faced workpiece can al so be leveled with this table. The leveling table can be used to align the surface to be tested with the detector reference plane while the operator is guided through the procedure by screen prompts. 3-axis Adjustment Table <Option> 178-047 DAT Function for the leveling table <Option> Aligned Not aligned Recorded profiles Axial line Traverse direction Endpoint Start point Traverse direction Endpoint Axial line Start point Digimatic micrometer head Leveling table (DAT) (Option) 178-048 Inclination adjustment angle: ±1.5° Table dimensions: 130×100 mm Maximum load: 15 kg The height / tilt adjustment unit comes as standard for leveling the drive unit prior to making skidless measurements. When supported by guidance from the unique DAT function, it is also extremely easy to achieve highly accurate alignment. Combining (adjustment guidance) Powerful support for leveling Preliminary measurement Turn tilt adjustment knob by specified amount Final measurement With DAT Without DAT DAT screen (adjustment guidance) Repeat OK NG Estimating size of tilt Accurate leveling Reduce setting time Preliminary measurement Intuitive adjustment using the tilt adjustment knob Confirmation measurement Simple operation
6 Anyone can easily perform high-level data collection. This unit allows you to load Surftest SJ-410 calculation results (SPC output) into commercial spreadsheet software on a PC via USB connector. By enabling one-touch operation for entering calculation results instantaneously, the USB Input Tool improves efficiency and helps reduce human error. USB keyboard signal conver sion t ype* I T- 016U 26 4 - 016 -10 * Requires the optional Sur f tes t S J - 410 connec tion cable. 1 m: 936937 2 m: 965014 USB Input Tool Direc t U S B - I T N - D 0 6AFM38 0D This unit allows you to remotely load Surftest SJ-410 calculation results (SPC output) into commercial spreadsheet software on a PC. By enabling one-touch operation for entering calculation results at a distance, the U-WAVE system improves efficiency and helps reduce human error. U-WAVE-T* (Connects to the SJ-410) 02 A ZD 8 8 0G * Requires the optional Sur f tes t S J - 410 connec tion cable. 02AZD790D U-WAVE-R (Connects to the PC) 02 A ZD 810D Wireless and quick capture of measurement results on a PC - no more handwriting, as data can be input easily with a single touch <Option> Wireless Input Tool U-WAVE One-touch Input USB Input Tool ● ● ● ● ● ● ● ● + + Higher level of quality control Wireless communication and advanced analysis User benefit2 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●●●●●●●●●●
7 Contour / Roughness analysis software FORMTRACEPAK-AP The Sur f tes t S J - 410 Series has a USB inter face, enabling measurement condition setup and s tar t via PC . We al so provide a program that let s you create inspec tion record tables using a Microsof t Excel* macro. ● OS: Windows 7 Windows 8 Windows 10 ● Spreadsheet software: Microsoft Excel 2010 Microsoft Excel 2013 Microsoft Excel 2016 Required environment* This program can be downloaded free of charge from the Mitutoyo website. ht tps : / /mi tutoyo . eu/en_us /down l oads / sof tware - and-updates For SURFTEST SJ-410 Series USB Communication Tool (Free software) The optional USB cable is also required. USB c able for S J - 410 Serie s 12AAD510 * W indow s OS and Mi cros of t E xcel are produc t s of Mi cros of t Corporat ion. More advanced analysis can be per formed by loading S J - 410 Series measurement data to FORMTR ACEPAK-AP via a memor y card (option) for proces sing back at base. Usually, a spherical or cylindrical surface (R-surface) cannot be evaluated, but, by removing the radius with a filter, R-surface data is processed as if taken from a flat surface. Other curved surfaces can be processed besides cylindrical, such as parabolical and ellipsoidal. Easily measures R-surface roughness (skidless measurement) Typical applications Surface roughness measurement requires a run-up distance before starting the actual measurement (or retrieving data). When the SJ-410 Series measures, its run-up distance is normally set to 0.5 mm. However, this distance can be shortened to 0.15 mm using the narrow-part measurement function. This function extends the measurement of narrow locations to features such as piston-ring grooves and O-ring grooves. Narrow-part measurement feature 3.5 0.5 0.5 2.5 0.1 Overruns sur face using 0.5 mm run-up Run-up of 0.5 mm is not enough for performing the measurement Evaluation length λc=2.5 mm 1 sampling length Evaluation length λc=0.8 mm 1 sampling length 2.5 ø1.2 1.3 St ylus Workpiece 1.8 A wide range, high-resolution detector Detector Measuring range / resolution: 800 µm / 0.01 µm 80 µm / 0.001 µm 8 µm / 0.0001 µm High straightness drive unit Drive unit Straightness / traverse length: 0.3 µm / 25 mm (SJ-411) 0.5 µm / 50 mm (SJ-412) High-accuracy measurements with selectable drive unit SJ-412 SJ-411 Use the USB Communication Tool to create inspection record tables and perform advanced analysis Example: surface roughness measurement of piston-ring groove Example: surface roughness measurement of O-ring groove R-Surface compensation Actual profile Filtered profile Circular component Surface roughness component Surface roughness component Circular component Removed
8 Area Coordinate difference Step Point group data collected for surface roughness evaluation is used to perform simplified contour analysis (step, step height, area, and coordinate difference). It assesses minute forms that cannot be assessed by a regular contour measuring machine. Simple contour analysis function Doing double duty for space saving Surface Roughness / Fine Contour User benefit3 Skidless measurement Skidless measurement is where surface features are measured relative to the drive unit reference surface. This measures waviness and finely stepped features accurately, in addition to surface roughness, but the range is limited to the available stylus travel. Skidded measurement In skidded measurements, surface features are measured with reference to a skid following close behind the stylus. This cannot measure waviness and stepped features exactly but the range of movement within which measurement can be made is greater because the skid tracks the workpiece surface contour. Your choice of skidless or skidded measurement Measuring example of stepped features: Skidless Measuring example of stepped features: Skidded 測 定 Measured profile Measured profile Fulcrum point of Stylus Stylus Detector Traverse direction 測 定 Fulcrum point of Stylus Stylus Skid Detector Fulcrum point of Skid Traverse direction 測 定 Traverse direction 測 定 Traverse direction Traverse direction Supports not only surface roughness measurement but also fine contour measurement
9 The unit is easily transported in a dedicated carrying case which includes holders for the accessories as well as the tester itself. (Standard accessory) This portable surface roughness tester is equipped with analysis functionality rivaling that of benchtop surface roughness testers. Equipped with convenient carrying case as standard Easy to use and highly functional A variety of interfaces supplied as standard The external device interfaces that come as standard include USB, RS-232C, SPC output, and Footswitch I / F. Equipped with externally controllable interfaces as standard High-speed printer prints out measurement results on site A high-quality, high-speed thermal printer prints out measurement results. It can also print a BAC curve or an ADC curve as well as calculated results and assessed profiles. These results and profiles are printed out in landscape format, just as they appear on the color-graphic LCD. High-speed thermal printer built in Memory card (optional) is supported The measurement conditions and data can be stored in a memory card (optional) and recalled as required. This enables batch analysis and printout of data after on-site measurement. Measurement condition Internal memory: 10 sets Memory card: 500 sets Measurement result Memory card: 10000 sets Data storage Data compensation Simple contour analysis function
10 The tester includes X- and Y-axes micrometer heads. This makes axis alignment much easier because the tilt adjustment center is the same as the rotation center of the table. (Order No.178-042-1 / 178-043-1) Prec i s i on v i se Cylinder attachment Optional accessories, consumables, and others Micro vibration isolator types Reference step specimen Roughness specimen Ra 0,4 / Ra 3µm XY l eve l i ng tab l es Fit s on the s tand. This block can be positioned on top of cylindrical objects to perform measurements. 12AAB358 Diameter: ø15 to 60 mm Configuration ・ Cylindrical measurement block ・ Auxiliary block ・ Clamp Used to calibrate detector sensitivity. 178-611 Step nominal values: 2 µm / 10 µm 178-604 Movement is in X and Y axes only. Order No. Items 178-042-1 (mm) with digital heads 178-043-1 (mm) with analog heads 178-049 (mm) with digital heads Table dimensions 130×100 mm Maximum load 15 kg Inclination adjustment angle ±1,5° — Swiveling angle ±3° — X / Y-axis travel range ±12,5 mm ±12,5 mm ±12,5 mm Resolution 0,001 mm 0,01 mm 0,001 mm Dimensions (W×D×H) 262×233×83 mm 220×189×83 mm 262×233×55 mm Mass 6,3 kg 6 kg 5 kg Order No. 178 - 019 Clamp ing method Sl iding jaw s Jaw opening 36 mm Jaw w idth 4 4 mm Jaw depth 16 mm H e ight 38 mm Order No. Manual (M) or Auto (A) charged Loading Capacity Natural Frequenc y 178 - 023 -1 M 250 kg 2.0 - 3.0 Hz 178 - 0 93 -1 M 120 kg 2.0 - 3.0 Hz 178 - 025 A 250 kg 2.0 - 3.0 Hz 211- 013 A 150 kg 2.0 - 3.0 Hz Application 178-042-1 178-049 ●Printer paper (5 rolls) 270732 ●Touch-screen protector sheet (10 sheets) 12AAN040 ●Memory card* (2 GB) 12AAW452 ●Connecting cable (for RS-232C) 12AAA882D ●Footswitch 12AAJ088 * micro SD card (with a conversion adapter to SD card) Other Optional Accessories T-groove dimensions Unit: mm 7 4 3 13 (Auto charged pneumatic type) 211-013 178-093-1 (Manual charged pneumatic type)
11 Previously measured data can be recalculated for use in other evaluations by changing the current standard, assessed profile, and roughness parameters. Note: Some conditions are limited. This function allows a sampling length to be arbitrarily set in 0.01 mm increments (SJ-411: 0.1 mm to 25 mm, SJ-412: 0.1 mm to 50 mm). It also allows the SJ-410 Series to make both narrow and wide range measurements. The “OK” symbol means the measurement is within the limits set; “NG” means it is not, in which case an arrow points to either the upper or lower limit in the printout. A “GO/ NG” judgment s ymbol is displayed when limit s are set for the roughnes s parameter. In the case of “NG ,” the calculated result is highlighted and can al so be printed out . Recalculating Arbitrary sampling length setting GO / NG judgment function Access to functions can be restricted by a password A pre-registered password can limit use of measurement conditions and other settings to the tester’s administrator. Password protection Single-button measurements A sturdy sheet-button panel with superior durability in any environment is provided. For repeat measurement of the same work, simply pressing the start switch can complete measurement, analysis, and printout. Sheet buttons The display interface supports 16 languages. (Japanese, English, German, French, Italian, Spanish, Portuguese, Korean, Chinese (simplified / traditional), Czech, Polish, Hungarian, Turkish, Swedish, Dutch) Multilingual support Complies with many industry standards The Surftest SJ-410 complies with the following standards: JIS (JIS-B0601-2001, JIS-B0601-1994, JIS B0601-1982), VDA, ISO-1997, and ANSI. Applicable standards Enhanced standard functions
12 Detectors / Styli St yli Unit: mm Detectors Standard stylus For deep holes*6 2X stylus 12AAC740 (2 µm) 12AAB413 (5 µm)*5 12AAB425 (10 µm)*5 ( ): T ip radius 12AAE882 (1 µm) 12AAE924 (1 µm)*5 12AAC731 (2 µm) 12AAB403 (5 µm)*5 12AAB415 (10 µm)*5 12AAE883(250 µm)*8 ( ): T ip radius Nosepiece For standard measurement 12AAB344 Remarks ø2 to 20 For round bars 12AAB345 3X stylus 12AAC741 (2 µm) 12AAB414 (5 µm)*5 12AAB426 (10 µm)*5 ( ): T ip radius For small hole measurement Double-length for deep holes*6 12AAE898 (2 µm) 12AAE914 (5 µm)*5 ( ): T ip radius 12AAC732 (2 µm) 12AAB404 (5 µm)*5 12AAB416 (10 µm)*5 ( ): Tip radius Nosepiece For small hole measurement 12AAB346 Remarks Hole diameter: ø4 or more Hole depth: 15 or less For small holes Double-length for deep holes*6 12AAE892 (2 µm) 12AAE908 (5 µm)*5 ( ): T ip radius For extra-small holes 12AAC733 (2 µm) 12AAB405 (5 µm)*5 12AAB417 (10 µm)*5 ( ): T ip radius For small holes*6 *8 12AAE884 (ø1.6 mm) Nosepiece For ultra-small holes 12AAB347 Remarks Hole diameter: ø2.3 or more Hole depth: 6.5 or less For ultra-small holes*8 12AAJ662 ( ø 0.5 mm) For ultra-small holes 12AAC734 (2 µm) 12AAB406 (5 µm)*5 12AAB418 (10 µm)*5 ( ): T ip radius For small slotted holes*6 12AAE938 (2 µm) 12AAE940 (5 µm)*5 *5 T ip angle 90° *6 For downward-facing measurement only. 小穴用 Color coding*7 0.6 0.4 1.6 ø0.6 ø2.4 15 ø1.2 3.4 2.4 1.6 0.6 37.7 44.4 A Detail-A （S＝5/1） 60° 極細穴用 Color coding*7 0.4 1.2 ø2.4 8.9 ø0.6 2.5 37.7 1.2 44.2 A Detail-A ø0.3 （S＝5/1） 60° 超小穴用 Color coding*7 Detail-A ø0.3 0.8 0.4 （S＝5/1） ø2.4 37.7 2.5 ø0.6 8.9 44.2 0.8 A 60° 深穴用 深穴用3倍 Detail-A Detail-A ø2.4 87.7 0.9 94.7 7.6 5.2 A ø2.4 137.7 0.9 7.6 144.7 5.2 A Color coding*7 ø1.2 60° ø1.2 60° Color coding*7 深穴用 深 Detail-A Detail-A ø2.4 87.7 0.9 94.7 7.6 5.2 A 0.9 7.6 5.2 Color coding*7 ø1.2 60° 6 Color coding*7 深穴2倍用 3 1.8 0.6 ø2.4 94.7 87.7 0.9 小穴用・深穴2倍 ø1.2 1.6 3.4 2.4 ø2.4 94.4 87.7 0.6 30 A 0.6 ø0.6 Detail-A 細穴形状用 ø1.2 ø2.4 Ball ø1.6 41 87.7 93.8 極細穴形状用 ø2.4 ø0.3 A 7 37.7 43.8 7 ø0.5超硬球 A部詳細 ø2.4 43.8 37.7 8.5 3.1 A ø0.3 Ball ø0.5 Detail-A 細長穴用 ø0.3 0.4 1.6 ø1.2 ø2.4 94.4 87.7 0.6 45 A ø0.6 0.6 Detail-A 標準スタイラス 0.9 37.7 7.6 44.7 ø2.4 5.2 A Color coding*7 Detail-A ø1.2 60° ø1.4 R40 5.6 21.5 3.6 23.5 3.5 3.6 ø7.2 6.8 7.5 Stylus tip position 150° ø14 ø7.2 R40 3.6 23.5 3.5 6.7 3.6 5.6 21.5 2.8 Stylus tip position ø14 ø3 R40 0.6 1.6 3.6 21.5 5.6 3.6 23.5 1.4 3.5 15.6 ø7.2 3.8 R2 Stylus tip position ø14 R40 3.6 1.2 22.3 21.5 ø1.9 2 6.7 3.5 3.8 ø7.2 スタイラス先端位置 ø14 R40 3.6 1.2 22.3 21.5 ø1.9 2 6.7 3.5 3.8 ø7.2 Stylus tip position Order No. Measuring force 178-396-2*1*3 0,75 mN ’97ISO and ’01J IS compliant detec tor s 178-397-2*1*4 4 mN Detec tor s that compl y wi th prev ious s t andards, for general us e, etc. 178-396*2*3 0,75 mN ’97ISO and ’01J IS compliant detec tor s 178-397*2*4 4 mN Detec tor s that compl y wi th prev ious s t andards, for general us e, etc. *1 The skidless nosepiece (12AAB355) is a standard accessory. *2 The skidless nosepiece (12AAB355) and the nosepiece (12AAB344) are standard accessories. *3 The standard stylus (12AAC731) is a standard accessory. *4 The standard stylus (12AAB403) is a standard accessory. 14 60 ø8 ø14 Detector ø14 ø7 10 11.5 3.1 3.6 1.3 Skidless nosepiece （12AAB355） 4 ø14 ø14 ø7 6.8 3.6 14 60 27.2 ø8 ø14 24 10.4 2.8 10 3.1 3.6 1.3 Detector 検出器 Nosepiece Skidded ノーズピース スタイラス （12AAB344） Skidded Skidless *7 T ip radius 1 µm 2 µm 5 µm 10 µm 250 µm Color coding White Black No Color Yellow No notch or color *8 Used for calibration, a standard step gauge (178-611, option) is also required Unit: mm
13 For deep grooves (10 mm) 12AAC735 (2 µm) 12AAB409 (5 µm)*1 12AAB421 (10 µm)*1 ( ): T ip radius Nosepiece For deep grooves 10 12AAB349 Remarks Depth: 10 or less, Width: 9.5 or more For narrow grooves 12AAB350 Remarks Depth: 10 or less, Width: 3 or more For R-Surface 12AAB351 Remarks Convex: R1.5 or more Concave: R3 or more For vibration 12AAB352 For deep grooves*2(20 mm) 12AAC736 (2 µm) 12AAB408 (5 µm)*1 12AAB420 (10 µm)*1 ( ): T ip radius Nosepiece For deep grooves 20 12AAB348 Remarks Groove depth: 20 or less Groove pitches: 9.5 or more For deep grooves*2(30 mm) 12AAC737 (2 µm) 12AAB407 (5 µm)*1 12AAB419 (10 µm)*1 ( ): T ip radius For gear teeth 12AAB339 (2 µm) 12AAB410 (5 µm) 12AAB422 (10 µm) ( ): T ip radius Nosepiece For corners 12AAB353 For rolling circle waviness surfaces*4 12AAB338 (ø1.588) ( ): T ip radius *1 T ip angle 90° *2 For downward-facing measurement only. For knife-edges*4 12AAC738 (2 µm) 12AAB411 (5 µm)*1 12AAB423 (10 µm)*1 ( ): T ip radius Nosepiece For knife-edges 12AAB354 For eccentric arms*2 12AAC739 (2 µm) 12AAB412 (5 µm)*1 12AAB424 (10 µm)*1 ( ): T ip radius For deep grooves*2(20 mm) 12AAE893 (2 µm)*1 12AAE909 (5 µm) ( ): T ip radius For deep grooves*2(40 mm) 12AAE895 (2 µm)*1 12AAE911 (5 µm) ( ): T ip radius For deep grooves (30 mm) (length doubled for deeper variations) *2 12AAE894 (2 µm)*1 12AAE910 (5 µm) ( ): T ip radius For gear teeth (length doubled for deeper variations) *2 12AAE896 (2 µm)*1 12AAE912 (5 µm)*1 ( ): T ip radius For rolling circle waviness (length doubled for deeper variations) *2*4 12AAE886 (250 µm) ( ): T ip radius For corner holes (length doubled for deeper variations) *2 12AAM601 (2 µm) 12AAM603 (5 µm) ( ): T ip radius Hole-bottom cone stylus 12AAE899 (2 µm) 12AAE915 (5 µm)*1 ( ): T ip radius 23 0.9 φ2.4 24.2 φ1.2 90° 37.7 44.7 A 識別色 A部詳細 Color coding*3 Detail-A 60° 23 ø2.4 ø1.2 24.2 37.7 44.7 A 深溝用（20mm） 7.6 ø2.4 ø1.2 0.9 37.7 44.7 Ball ø1.588 5.2 転がり円 うねり用 23 21.8 5.2 95.2 87.7 ø2.4 ø1.2 深溝用2倍（20mm） 43.8 42.6 5.2 ø2.4 45.2 37.7 ø2.4 ø1.2 深溝用（40mm） 36.5 35 5.2 ø3 93.8 87.7 ø1.2 深溝用（30mm） 深穴2倍 36.5 35 ø3 93.8 6.77 87.7 ø1.2 60° 歯面用 深穴2倍 94.7 0.9 87.7 ø1.2 ø2.4 5.2 6.4 7.6 転がり円うねり・深穴2倍 93.8 87.7 φ1.2 60° 60° 7.6 6.4 φ2.4 穴測定コーナー用・深穴2倍 *3 T ip radius 2 µm 5 µm 10 µm Color coding Black No color Yellow *4 Used for calibration, a standard step gauge (178-611, option) is also required Note: Customized special interchageable styli are available on request. Please contact any Mitutoyo sales office for more information. 13 ø2.4 0.9 ø1.2 60° 14.2 37.7 44.7 A Color coding*3 Detail-A 深溝用（10mm） 33 31.8 5.2 ø1.2 A ø2.4 ø2.4 60° 37.7 45.2 Color coding*3 Detail-A 深溝用（30mm） 60° 7.6 6.4 37.7 43.8 ø1.2 ø2.4 A Color coding*3 Detail-A 歯面用 60° 60° 7.6 ø2.4 ø1.2 37.7 0.9 44.7 A Color coding*3 Detail-A ナイフエッジ用 A 37.7 0.9 90° ø1.2 45.2 7.6 10 ø2.4 ø2.4 識別色 A部詳細 Color coding*3 Detail-A 心 ø2.4 ø1.2 45.2 1.4 37.7 7.6 ø2.4 10 A 60° 穴底用 7.4 ø1 0.5 5 6.2 ø2.4 44.3 37.7 ø14 R40 17.9 ø7.2 3.5 21.5 5 3 3 1 3.6 4.5 13.4 9 1.4 5 11.6 10 R2 10 Stylus tip position ø14 ø7.2 （8.4） 3.6 3.8 19.5 1.8 21.5 3.5 13.4 2.5 5 9 10 Stylus tip position ø1.5 ø14 R40 12.8 0.6 1.4 1.4 3.5 3.8 19.5 1.8 21.5 4.5 3.6 10 9 ø7.2 Stylus tip position R2 4.4 ø14 ø7.2 R40 3.6 23.5 1.4 13.4 21.5 5.6 3.6 2.8 10 3.5 Stylus tip position R2 ø14 R40 3.5 3.8 19.5 1.8 21.5 22.8 0.6 1.4 27 20 ø7.2 9 Stylus tip position R2 4.4 1.4 コーナー用ノーズピース ø14 R40 1.4 3.5 0.5 21.5 ø7.2 19.7 2.3 6.1 4.5 0.6 1.4 3.6 R2 2.3 Stylus tip position 4.4 ナイフエッジ用ノーズピース ø14 R40 21.5 6.7 ø7.2 5.6 3.6 3.6 3.5 23.5 2.8 Stylus tip position Flat
14 Specifications Model No. SJ-411 SJ-412 Order No. mm 178-580-11 178-580-12 178-582-11 178-582-12 inch / mm 178-581-11 178-581-12 178-583-11 178-583-12 Measuring range X axis 25 mm 50 mm Z axis (detector) 800 µm, 80 µm, 8 µm Up to 2,400 µm when using an optional stylus. Detector Detection method Differential inductance Resolution 0,01 µm (800 µm range), 0,001 µm (80 µm range), 0,0001 µm (8 µm range) Stylus tip shape (Angle / Radius) 60° / 2 µm 90° / 5 µm 60° / 2 µm 90° / 5 µm Measuring force 0,75 mN 4 mN 0,75 mN 4 mN Radius of skid curvature 40 mm Measuring methods Skidless / Skidded (switchable) Drive unit (X axis) Measuring speed 0,05, 0,1, 0,2, 0,5, 1,0 mm/s Drive speed 0,5, 1, 2, 5 mm/s Straightness 0,3 µm / 25 mm 0,5 µm / 50 mm Up / down inclination unit Vertical travel 10 mm Inclination adjustment angle ±1,5° Applicable standards JIS 1982 / JIS 1994 / JIS 2001 / ISO 1997 / ANSI / VDA Parameter Ra, Rq, Rz, Ry, Rp, Rv, Rt, R3z, Rsk, Rku, Rc, RPc, RSm, Rmax* 1, Rz1max* 2, S, HSC, RzJIS* 3, Rppi, RΔa, RΔq, Rlr, Rmr, Rmr (c), Rσc, Rk, Rpk, Rvk, Mr1, Mr2, A1, A2, Vo, λa,λq, Lo, Rpm, tp* 4, Htp* 4, R, Rx, AR, W, AW, Wx, Wte Customizable Filtered profile Primary profile, Roughness profile, DF profile, Waviness profile, Roughness motif profile, Waviness motif profile Analysis graph Material ratio curve, Profile height amplitude distribution curve Data compensation functions Parabola, Hyperbola, Ellipse, Circle, Tilt, No compensation Filter 2CR, PC75, Gaussian Cutoff value λc 0.08, 0.25, 0.8, 2.5, 8 mm λs*5 2.5, 8, 25 µm Sampling length 0.08, 0.25, 0.8, 2.5, 8, 25 mm Number of intervals ×1, ×2, ×3, ×4, ×5, ×6, ×7, ×8, ×9, ×10, ×11, ×12, ×13, ×14, ×15, ×16, ×17, ×18, ×19, ×20 Arbitrary length 0,1 to 25 mm 0,1 to 50 mm Calculation display unit Customization Selection of display / evaluation roughness parameter Simplified contour analysis function Step, Step quantity, Area, Coordinate difference DAT (Digimatic Adjustment Table) function Helps to level workpiece prior to skidless measurement Real sampling function Inputs the displacement of the detector while stopping the drive unit statistical processing Calculates the maximum value, minimum value, average value, standard deviation, pass rate and histogram for each parameter. Judgment*6 Maximum value rule, 16 % rule, mean value rule, standard deviation (1σ, 2σ, 3σ) Storing measurement condition Max. 10 (calculation display unit) Print function (Built-in thermal printer) Measurement condition / Calculation result / Judgment result / Calculation result per segment / Tolerance value / Evaluation curve / Graphic curve / Material ratio curve / Profile height amplitude distribution curve / Environmental setting items / Statistical result (Histogram) Display language 16 languages (Japanese, English, German, French, Italian, Spanish, Portuguese, Korean, Chinese (simplified / traditional), Czech, Polish, Hungarian,Turkish, Swedish, Dutch) Storage function Built-in memory: Measurement condition (Up to 10) Memory card (optional): 500 measurement conditions, 10000 measured profiles, 500 display images, 10000 text files, 500 statistical data, 1 backup file of device setting data, 10 data of Trace 10 External I / O functions USB I / F, Digimat ic output , R S -232C I / F, F oot s wi tch I / F Power supply Bat ter y Charging t ime / Endurance Buil t- in bat ter y (rechargeable N i - MH bat ter y) / AC adapter Charging t ime of the buil t- in bat ter y : about 4 hour s (may var y due to ambient temperature) Endurance: about 10 0 0 measurement s (di f fer s slight l y due to us e condi t ions / env ironment ) Ma x . power consumpt ion 50 W External dimensions (W×D×H) Calculat ion display uni t 275×198×109 mm Up / down inclinat ion uni t 130,9×63×99 mm Dr i ve uni t 128×35,8×46,6 mm 154,5×35,8×46,6 mm Mass Calculat ion display uni t 1,7 kg Up / down inclinat ion uni t 0,4 kg Dr i ve uni t 0,6 kg 0,64 kg Standard Accessories Detec tor*7/ St andard s t y lus*8 178 - 6 01 Roughnes s specimen (Ra3 µm) 270732 Re ceipt paper (St andard t ype: 5 - roll s et ) 12BAL 4 02 P rotec t i ve sheet for the LCD (×1 sheet ) 12BAG 83 4 Touch pen 12 A AN 0 41 Car r y ing cas e AC adapter, Power cable, Flat- blade s crewdr i ver, Phillips s crewdr i ver, Hex wrench, Strap for the touch pen, Operat ion manual, One - sheet manual, War rant y card *1 Calculation is available only when selecting the VDA, ANSI, or JIS 1982 standards. *2 Calculation is available only when selecting the ISO 1997 standard. *3 Calculation is available only when selecting the JIS 2001 standard. *4 Calculation is available only when selecting the ANSI standard. *5 Not available when selecting the JIS 1982 standard. *6 Only the mean value rule is available for the ANSI standard. 16 % rule is not available when selecting the VDA standard. *7 Depending on the Order No. of the SJ-410 Series main unit, 178-396-2 or 178-397-2 is provided as standard. *8 Standard stylus (12AAC731 or 12AAB403) supporting the provided detector is provided as standard. Note 1: Refer to pages 12 to 13 for details of Detector, Stylus and Nosepiece. N ote 2: To denote your AC line vol t age add the following suf f i xes (e.g. 178 - 56 0 -11A). A for 120 V, C for 10 0 V, D for 230 V, E for 230 V (for UK ), DC for 220 V (for China), K for 220 V (for Korea)
15 Dimensions ±1.5° 130.9 45.8 90 ø14 35.8 63 99 219.3 33.5 (0.9) 25.4 54 10 Connecting cable (1.5 m) (50.8) (60) (245.8) T ilting range Vertical travel length 15° 198 109 275 Example of mounting on a simple column stand. (178-039)*1 *1 For details see page 5. 12 250 25 （50） 120 40 60 578 175 （201.5） 35*2 250 400 Code No.178-039 簡易スタ ンド外観寸法図 Measuring range 15 8.5 7 11 T-groove dimensions Unit: mm Unit: mm *2 This is the lowest position of the standard stylus mounted on the simple column stand. Since it is 35 mm from the base top, a block of suitable height is required for calibration with a roughness specimen. Use the stand in combination with optional accessories such as a leveling table (178-016) or an XY leveling table (178-024). Note: The dimensions in parentheses indicate those for SJ-412 Note: Dimensions in parentheses indicate those of SJ-412 [equipped with a 50 mm drive unit].
Coordinate Measuring Machines Sensor Systems Vision Measuring Systems Test Equipment and Seismometers Form Measurement Digital Scale and DRO Systems Optical Measuring Small Tool Instruments and Data Management Find additional product literature and our complete catalog here. www.mitutoyo.eu Mitutoyo Europe GmbH Borsigstraße 8-10 41469 Neuss Tel. +49 (0) 2137-102-0 info@mitutoyo.eu www.mitutoyo.eu Note: Product illustrations are without obligation. Product descriptions, in particular all technical specifications, are only binding when explicitly agreed upon. MITUTOYO and MiCAT are either registered trademarks or trademarks of Mitutoyo Corp. in Japan and/or other countries/regions. Other product, company, and brand names mentioned herein are for identification purposes only and may be the trademarks of their respective holders. © MITUTOYO/D 10/20 PRE1534 Mitutoyo supports you from start to finish. Mitutoyo is not only a manufacturer of top-quality measuring products but one that also offers qualified support for the lifetime of the equipment backed up by comprehensive services, ensuring your staff can make the very best use of the investment. Apart from the basics of calibration and repair, Mitutoyo offers product and metrology training, as well as IT support for the sophisticated software used in modern measuring technology. We can also design, build, test, and deliver bespoke measuring solutions and even, if deemed cost-effective, take your critical measurement challenges in-house on a sub-contract basis.
RkJQdWJsaXNoZXIy